Nessun prodotto
I prezzi sono IVA inclusa
Subcategories
Il nostro monitor delle prestazioni più avanzato. È dotato di un sistema wireless per il monitoraggio della frequenza cardiaca, la possibilità di memorizzare allenamenti in una pennetta USB flash drive (in vendita separatamente), e la retroilluminazione per una visibilità impeccabile anche in ambienti poco luminosi.
For use on all Model C, D and E Indoor Rowers. Includes seat top, seat frame, seat rollers and hardware. See more info.
For use with Model C, D and E Indoor Rowers. Includes on 8' 4" long chain with a brass swivel at the handle end and chain connectors for the inside end. If your chain is badly rusted, has seized links or is broken, you will need to replace it with this part. See more info.
For use with Model D and E Indoor Rowers. This is the generator base and coil that transmit flywheel motion to and generates power for the Performance Monitor on your indoor rower. See more info.
For use with Model D and E Indoor Rowers and the SkiErg. This is the sensor coil for the power generator that transmits flywheel motion to and generates power for the Performance Monitor on your indoor rower or SkiErg. See more info.
For use on the Model D and E Indoor Rower. This is the 14 tooth sprocket for the flywheel axle. If you need to replace the sprocket, you should replace the chain at the same time. See part number 1915. See more info.
For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws (4) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney" shaped seat. See more info.
For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...
For use with Model C, D and E Indoor Rowers. This is the 12´ 6" long elastic shock cord (or bungee cord) that recoils the chain on recovery. If your chain recoils slowly—or not at all—between strokes, then you should inspect your existing shock cord. See more info. Note: Shock cord may be white or green.
For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...
For use with updated Model D, Model E and Dynamic Indoor Rowers. Replacement nylon footstrap with buckle, approximately 30" long by 1" wide with a screwhole drilled approximately 9" from the buckle end. Two per machine. Sold individually. Model D/E Flexfoot Assembly Diagram
For use with all Model D and Model E Indoor Rowers manufactured from August 2006–present.
For use on all Model B, C, D, and E Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013 or 258 depending on which model you have) is sold separately. See more info.
For use with Model C and D Indoor Rowers and all SkiErgs Plastic cover for the bearing on the left side of the Model C or D Indoor Rower, opposite the flywheel, and the back side of all SkiErgs.
For use on all Model C, D, E and Dynamic Indoor Rowers as well as all SkiErgs. This is the rubber bearing cup that holds the R8 bearing on indoor rowers (part number 232, sold separately) and the 12mm bearing on SkiErgs. See more info.